收藏本站
SAW Components
SAW RF filter
B3583
345.0 MHz
Data sheet
ESD protection of SAW filters
SAW filters are E lectro S tatic D ischarge sensitive devices. To reduce the probability of damages
caused by ESD, special matching topologies have to be applied.
In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is
expected.
Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore
only the input matching of the SAW filter has to be designed to short circuit or to block the ESD
pulse.
Below three figures show recommended “ESD matching” topologies.
For wideband filters the high-pass ESD matching structure needs to be at least of 3 rd order to
ensure a proper matching for any impedance value of antenna and SAW filter input. The required
component values have to be determined from case to case.
Cs1
Cs3
Cs1
Cs3
Lp2
to output
matching
Lp2
to output
matching
Fig. 1 MLC varistor plus ESD matching
Fig. 2 Suppressor diode plus ESD matching
In cases where minor ESD occur, following simplified “ESD matching” topologies can be used
alternatively.
Cs1
Cs3
Lp2
to output
matching
Fig. 3 3 rd order high-pass structure for basic ESD protection
In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper
length and width. If this configuration is possible depends on the operating frequency and
available pcb space.
Effectiveness of the applied ESD protection has to be checked according to relevant industry
standards or customer specific requirements
For further information, please refer to EPCOS Application report:
“ ESD protection for SAW filters ”.
This report can be found under www.epcos.com/rke.Click on “Applications Notes”.
Please read cautions and warnings and
important notes at the end of this document.
5
October 22, 2013
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
B39361X6865N201 FILTER SAW BANDPASS 36.125MHZ
B39389J3353K100 FILTER IF 38.9MHZ 10DIP
B39391B3684U310 FILTER SAW 387.5MHZ LOWLOSS SMD
B39391R972H110 R 972 390MHZ
B39431B3710U410 FILTER SAW 433.92MHZ REMOTE SMD
B39431B3721U410 FILTER SAW 433.92MHZ SMD
B39431B3727H110 FILTER SAW 433.92MHZ SMD
B39431B3730H110 FILTER SAW 433.92MHZ SMD
相关代理商/技术参数
B39351B3680U310 功能描述:信号调节 LOW LOSS 352 MHZ RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39351-B3680-U310 制造商:EPCOS 制造商全称:EPCOS 功能描述:SAW Components Low-Loss Filter 352,0 MHz
B39351B5073Z810 功能描述:信号调节 RF 355MHZ RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39351-B5073-Z810 制造商:EPCOS 制造商全称:EPCOS 功能描述:SAW RF filter TETRA
B39351R 802H210 制造商:TDK-EPC 功能描述:- Tape and Reel
B39351R802H210 功能描述:信号调节 345MHz Resonator RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39351-R965-H110 制造商:EPCOS 制造商全称:EPCOS 功能描述:SAW Components SAW resonator Short range devices
B39358-X6753-M100 制造商:EPCOS 制造商全称:EPCOS 功能描述:SAW bandpass filter Bandpass filters for terrestrial TV applications